Take the 2-minute tour ×
Seasoned Advice is a question and answer site for professional and amateur chefs. It's 100% free, no registration required.

I'd always wondered. The blocks usually seemed designed to have the knives go in blade down, so that the blade touched wood coming in and out. But I know that when I whittle, cutting the wood wears the blade of a knife down very, very quickly. I'd always wondered if that regular contact with the wood from sliding into and out of the blocks could be wearing my knives down. Does it? If so, does putting them in blade up (against the design of the block - it would seem) do any better for them?

share|improve this question
1  
Check your knives too, mine are weighted so that when inserted into the knife block, the non-blade side presses against the top of the slot. This means the blades don't touch the wood. –  C4H5As Apr 17 '11 at 2:52
add comment

8 Answers

up vote 13 down vote accepted

Wooden blocks are ideal for knife storage because they keep the blades dry (the wood absorbs some of the humidity in the air), preventing rusting.

The motion of inserting and withdrawing blades over wood will not noticeably dull them, because you're not actually cutting the wood or indeed even applying any pressure as you do so.

A good tip is to use a good quality steel to sharpen your knives with just one or two passes on each side before each use. Wash them with hot water by hand, avoiding dishwashers unless you like replacing your knives annually, then return them to the block once they're fully dried.

share|improve this answer
5  
I'd like to point out that it's a honing steel you use before each use. It hones, and does not sharpen. There is a significant difference. If you were sharpening a knife before each use it would quickly erode to nothing. –  hobodave Jul 18 '10 at 21:10
1  
Very good point, thanks for the clarification. I'd suggest that if you hone regularly from new then sharpening should be something you have to do very rarely. –  bbodien Jul 19 '10 at 10:09
add comment

Yes, they can wear a bit in a vertical block, but only if you store them point-side down. When I had a vertical block, I stored them points-up. Assuming there's a little extra room in the slots, the tip should touch nothing when you remove the knives.

share|improve this answer
add comment

Frankly, I think the constant up and down and sliding across the maple cutting board will do much more to dull my knives than storing them in a vertical slot block.

share|improve this answer
add comment

Technically, yes. While wood is a preferable surface to many others for drawing your blade across it will still cause wear. If you're using a block, the slots should be horizontal.

Your knife block is poorly designed. I have a Shun knife block, the blades go in sideways. I just searched for J.A. Henckels and Wusthof blocks on Amazon as well, all horizontal.

Is this worth buying a new block over? Probably not, as the other answers in this thread indicate, it's not that big of a deal. It is less than ideal however.

share|improve this answer
add comment

We have two knife blocks. One has vertical holes, the other has horizontal holes. The horizontal block gives us all the advantages of wood, without the big disadvantage you just pointed out. The cutting edges don't rest against wood all the time, and are less likely to be in contact with said wood when being placed/removed.

share|improve this answer
add comment

It's much better to put the knife in a wooden block than to put it in a drawer and have it rattle around with other metallic objects. Most pro knife sets come with a wooden block so I would assume that is the preferred storage method.

If you are concerned that pulling the knives out along the wood will dull the blade than as you pull out, also pull away from the blade side so the knife blade doesn't rub against the wood.

share|improve this answer
add comment

It shouldn't matter all that much. I prefer a magnetic strip on the wall, though.

share|improve this answer
add comment

I'm not a whittler, but I think that what causes the blade to wear is pulling it across the wood. The blade should be fine as long as it is drawn lengthwise (like you are cutting something in half). Blades are very strong this way, but since the edge is very thin, it can easily be bent by having things pull across it.

Since wood is much softer than metal, I suspect there would be very little impact on the integrity of the blade. It it were pushed very hard into the wood, it might bend, but under normal use, I can't see any problems.

share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.