Take the 2-minute tour ×
Seasoned Advice is a question and answer site for professional and amateur chefs. It's 100% free, no registration required.

As we've rolled into fruit season this year I've started canning up some jams using a traditional boiling process in my big stock pot (though I'm getting pretty close to investing in a pressure canner at this point) and I'm running into a problem: I wind up with too much jam to process in a single batch (which comfortably handles about 7 4-ounce jars or 4 8-ounce jars), so I'm forced to do one batch, then sterilize a new set of jars before I can process another batch — and in the meantime, my jam is continuing to cook down, pushing past 220F/105C and taking on a much thicker, taffy-like consistency. Is there any way of keeping my texture consistent across batches, or should I just be making smaller loads or accepting the difference in results?

share|improve this question
    
I'm not a canning expert but... why are you continuing to cook the rest of the batch while you're canning the first part? –  Jefromi Jul 17 '12 at 20:24
    
As long as your cooked jam doesn't fall under 60°C, you can keep it off the flame. Measure with a candy thermometer to be sure. –  rumtscho Jul 17 '12 at 20:28
    
@rumtscho Sounds like that's an answer? Do you also need to reheat it before processing, so that the processing time is all at the temperature it's meant to be? –  Jefromi Jul 17 '12 at 20:30
    
@Jefromi I basically kill the heat beneath it, but at that level of sugar (and given the cast-iron pot) it seems to be retaining enough heat that it will cheerfully just keep cooking itself whether it's on the heat or not... –  Steven Stadnicki Jul 17 '12 at 21:21
1  
Maybe I'm wrong but I thought you didn't have to sterilize the jars if you're processing for at least 10 minutes in the hot water bath. I always process at least 10 minutes and so skip the pre-sterilization of the jars. (Looks like this webpage also backs me up: simplycanning.com/sterilizing-jars.html) –  lemontwist Jul 17 '12 at 23:06

2 Answers 2

If it's getting cooked too much, well, stop cooking it. You can cover it to prevent water loss. If it's too hot sitting on the same burner (on an electric stove), move the pot. It sounds like your cast-iron pot might be part of the problem, too - if it's still staying too hot, you could pour it into something else. Finally, if you do still have significant water loss, I believe you should be able to add a little water (careful not to add too much) and stir and reheat.

P.S. you could also just get a lighter pot. (I know that's not ideal.)

share|improve this answer

You could avoid the problems by having more jars ready. Here's what I do to get my jars ready.

*When you want to clean jars up for canning, the sterilizing process is between you and yours, not the health authorities.

Here is what I do to clean up my jars quickly. I save jars where the lid acts as a button indicator - if the button is popped up, you don't use it when you bought it in a shop.

First, you wash the jar immediately you empty it in the normal way. Then you put about 2cm to 3cm of water into the jar and microwave it for around a minute, so that the water boils.

Take the jar out carefully - use a cloth or oven glove, it is HOT, and be aware that it may spontaneously "bump" - moving it could cause the boiling water to jump out of the jar, do not point it at your face. Prod it with something long, like a wooden spoon, before you pick it up.

Screw the cap back on. Turn it upside down so that the hot water contacts the inside of the lid. If the water leaks out at this point, don't use that jar - the seal would be OK in an industrial process, but it will not be useful for this trick.

Stand the jar on one side until it cools, add it to your collection.

When the time comes that you want to use the jars, pick out enough to do the job and repeat the boiling out process once again, being sure to only use jars that have properly sealed - the button pops up again to tell you the seal was effective, something will grow in the water if the job was not done right.

Then you make the jam or chutney to put into the jars.

This way you never become short of jars. If you do not pick out enough, it is the work of a couple of minutes to make another jar ready. If you pick out too many, you can put the surplus back into your stockpile.*

If it makes you feel more secure, you can use the solution for sterilizing baby feed bottles to immerse the jar lids during the process, but you must rinse off that solution before you re-fit the lids on the jars.

Wet heat kills more bugs than dry heat ... this way, it is a matter of moments to have extra jars ready - or more than you really need, you don't waste any sterilized jars.

I've taken to using this trick so I can use portions from a jar of, say, pasta sauce. When I use half the jar, I microwave it for a minute and put the lid back, then stand it to cool before I put it in the fridge.

Not properly and fully tested as a method, but I've been doing this for a year now without ill effects.

share|improve this answer
    
Do you happen to have any other data about the safety of that method? It sounds handy, but canning isn't an area I like to play around with relatively untested methods. –  Jefromi Jul 17 '12 at 21:57
    
No data - I don't have a microbiology lab to play in these days. I'm just improvising with what I have to hand. That said, the biggest risk when canning things at home is from spore-forming bacteria getting into the final product. They don't form spores when there is water about, and the vegetative organisms would die in the steam and boiling water. If you really want to go "belt and braces", put the jars containing whatever you've canned in a pressure cooker with all the weights on and boil it for 20 min per load. That will make whatever it is keep for years. –  klypos Jul 17 '12 at 22:22
    
I wasn't suggesting that you would personally test it. There's tons of literature out there about canning. –  Jefromi Jul 18 '12 at 2:53
2  
Wait, is that link your own website? You should probably mention that in your answer; the way you have it now gives the impression that there are at two people doing this, which makes it look slightly better-tested. –  Jefromi Jul 18 '12 at 3:02
    
When I tried to post all the info it didn't work, I hit some kind of length limit - I think that has more to do with Windows7 than anything else - so I put that part on a holding page. You could call it "my website", but the page you see is all of it! When I try to edit the post, I'm back to my original problem. I'll see if I can sort it out today. –  klypos Jul 18 '12 at 12:23

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.