Take the 2-minute tour ×
Seasoned Advice is a question and answer site for professional and amateur chefs. It's 100% free, no registration required.

I'm doing something really simple right now, sprinkling pepper over one side of a half-inch thick steak and throwing it in a pan of butter.

But by the time it's cooked through (I want medium rare), the outside is just a sickly grey.

How can I get the steak to look good?

Edit:

They're actually even thinner, maybe less than half an inch. And they keep cooking through to well done and grey on the inside almost immediately!

share|improve this question
2  
Use a hotter pan? –  TFD Jan 4 '13 at 3:06
    
Found old answers to a similar question How do you properly cook a steak? –  Stefan Jan 4 '13 at 6:17
    
how thick are these items, actually? Do you perhaps have cutlets instead of steaks? If not, do you know what actual cut the steaks are? –  SAJ14SAJ Jan 4 '13 at 17:54
    
VERY thin. They vary between a quarter inch and half an inch. spiceyokokoo's tips worked reasonably well, although the steaks are still largely grey when they're done. –  Aerovistae Jan 4 '13 at 20:01
    
We (in the UK) would call the 1/4 inch ones Minute Steaks, because they only take minutes to cook - jamieshomecookingskills.com/recipe.php?title=minute-steak But they're still coming out grey? What kind of pan and oil are you using? –  spiceyokooko Jan 4 '13 at 20:30
add comment

5 Answers

up vote 9 down vote accepted

I would actually recommend the opposite of what was said above. Since the meat is so thin you may have much better results pan searing it in an extremely hot pan from slightly frozen. This way the outermost layer will start to undergo the maillard reaction long before the inside of the steak reaches a medium-rare temp and will give you a better chance of preventing it from overcooking.

This link provides an overview of the process for a much larger piece of meat then your using but the searing process is what your concerned most with since your steaks are so thin. You will likely have to play with the timing a little bit with regards to how frozen the steak needs to start out but I figure erring on the side of too frozen is best since you can then heat them in the oven to the internal temp your looking for.

http://www.thekitchn.com/for-the-perfect-steak-first-freeze-it-solid-then-cook-for-an-hour-165793

share|improve this answer
    
That should work if you are prepared to freeze the steak, but how do I get the steak flat enough to be heated, I need to press it when freezing? Think you need a blow torch to make it work? –  Stefan Jan 4 '13 at 5:54
    
@Stefan A 650°F (~350°C) cast iron pan will do fine. Sear will be done in well under a minute per side (I'd check after 15s or so). No need for a torch. (And you'll probably have to put the butter on afterwards, it'll burn...) –  derobert Jan 4 '13 at 12:57
    
A torch would work but isn't the most efficient option. I reccomend freezing the steak between two sheet pans with a sturdy weight on top to create a nice flat surface. –  Brendan Jan 5 '13 at 17:13
    
I wish I had that much space in my freezer :-) –  Stefan Jan 7 '13 at 6:18
1  
@Hanno Fietz, Here the flipping technique works against this technique. You use flipping every 15-30 sec to get the inside to heat more evenly and reduce the total cooking time, with this technique, you want to maximize the outside heating so it is probably better to not flip. –  Stefan Jan 8 '13 at 5:06
show 1 more comment

1) Let the pan be as hot as possible, add meat just before the oil starts to smoke.

2) Make sure the meat is NOT wet, dry it, water will steam before you get the steak to look nice, making that steam will reduce the temperature in the pan and not enough heat is left to make the steak look nice.

3) Do not put to much stuff in the pan, do only one or two steak at a time, do not fill the whole pan.

4) Use a pan with lots of 'thermal capacity' I.e. a heavy/thick iron pan, not a thin pan. This means that you have lots of heat stored in the pan and it will not get cold so fast.

share|improve this answer
add comment

How to get the steak to look good?

Two tips –

1 Don't use butter.

2 Flash-fry it.

Flash frying is cooking very quickly in very hot oil. Given the thickness of your steaks and that you want them medium-rare the whole process happens very quickly.

On a high heat sear/seal one side, turnover and seal the other side, turn the temperature down and cook till medium-rare, the whole process really should only take minutes.

Don't use butter to fry them in. At the temperature you require to flash-fry butter will burn. Use a higher temperature oil such as vegetable, corn or nut.

share|improve this answer
add comment

If you want the absolute hottest temperature, I suggest using a charcoal grill if you have one.

share|improve this answer
    
Unfortunately not at this particular juncture in my life. –  Aerovistae Jan 4 '13 at 20:10
add comment

The pan might be simply conducting too much heat into the thin steak to brown the outside before the inside is finished. Charcoal is a slower application of heat, and works by radiative heat instead of conductive. While such a grill can be a luxury, the broiler in your oven may have the same effect. Put the steak in a cool pan, toss under the broiler, and flip when its brown.

share|improve this answer
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.