Sign up ×
Seasoned Advice is a question and answer site for professional and amateur chefs. It's 100% free, no registration required.

I'm sure everyone's seen this - that brownish stuff left behind when you grease an area of a baking dish that gets left exposed to the heat. Soap doesn't bother it too much, and it likes to gum up my scrubber. What's going on there, and are there any easy ways to get it off?

share|improve this question
Your spray/oil is a drying or semi-drying oil. Switch to something less unsaturated, and your troubles will decrease: I use mostly olive oil. Coconut, palm, canola or peanut oil would also work. Corn and soybean oils are disasters waiting to happen. –  Wayfaring Stranger Jun 6 at 12:11

5 Answers 5

up vote 6 down vote accepted

When oil gets overheated, it turns into a polymer that is insoluble in water, even with soap.

The best way to clean this up is with Barkeeper's Friend, Bon Ami, or a similar solvent (I think they're all alkaline-based solvents). It's non-abrasive, and safe to use on almost all cookware without leaving marks.

Edit: To help prevent this from happening in the future, use a paper towel to wipe off any excess baking spray on the edges of the baking dish that won't be covered by food.

share|improve this answer
To expand on what Bob said -- basically, the oil polymerization is the exact process that you're trying to get when you season cast iron ... it just really sucks when it's all splotchy on your other pans. –  Joe Nov 8 '10 at 14:40
Yeah, I know, best solution is not to let it happen - but sometimes you forget, or miss a spot. As for the cleaning tips, thanks - though I don't think alkalinity is the factor there. Wikipedia says Barkeeper's Friend's active ingredient is oxalic acid, while Bon Ami's listed active ingredients are sodium carbonate, calcium carbonate, and feldspar (described there as mild abrasives, though obviously alkaline too). I'm sure both work great though! –  Jefromi Nov 8 '10 at 14:41
I probably sound like a broken record chiming in on every thread about cleaning, but I live and die by my Barkeeper's Friend! –  stephennmcdonald Nov 8 '10 at 16:48
Dunno about Barkeeper's Friend, but Bon Ami is, indeed, an abrasive. It's less likely to scratch than some other scouring powders that aren't milled as finely, but its primary cleaning action is still mechanical rather than chemical. –  Marti Nov 8 '10 at 19:23
I just soak the pan in water for a day or two, which loosens it enough to scrub off without any other gunk. –  Bruce Alderson Nov 8 '10 at 19:53

Place your baking dish in a larger baking pan & squeeze soap dish over it plus a couple of handfuls of baking soda then add hot water to cover the dirty baking dish. Let it soak for an hour of so then just scrub with a brush & that's it!

You can buy a large box of baking soda at Smart & Final or Sam's Club or Costco. The baking soda will not scratch your baking dish.

share|improve this answer

Comet and a small scrub brush with a handle . I bought a wooden handle metal bristol small brush generally used to scrub battery acid off and use on my stainless steel pots and pans. I am sure it would work on glass too.

share|improve this answer

I used a Mr. Clean Magic Eraser last night on my deep fryer. It took a little elbow grease but it came right off, no chemicals needed

share|improve this answer

I don't know of any method for the burnt-on oil in particular, but for difficult to clean pans in general, I usually resort to razor blades (not cartridge ones though). Something like a proper scraper tool would be even better.

Basically, something really sharp that can get underneath the substance, and then it can't help but come off.

Chemically, I'm assuming the stuff left on the pan after the cooking process wouldn't be the oil, since that comes off in soap. I suspect (guessing here) that it's the propellant from the can. Which isn't really that much of a pleasant thought.

share|improve this answer
The same thing happens if you oil the pan the traditional way rather than using a spray, so it has nothing to do with the propellant. –  Marti Nov 8 '10 at 16:27

Your Answer


By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.