When making french press coffee, you are often instructed to "bloom" the grounds by adding a small quantity of boiling water, stirring the grounds into a slurry, and then adding the rest of the water.

What I don't understand is... Why?

For clarification, most other situations where you are instructed to bloom something it makes sense to me - cornstarch being added to soup needs to fully hydrate before it hits the hot water to not get clumpy, "active dry" baking yeast needs to dissolve the pellets and start releasing nutrients to the yeast before being diluted in the dough, and gelatin needs to hydrate fully being integrated with other ingredients without clumping. The coffee case seems mysterious to me.

  • Sounds like marketing flap
    – TFD
    Feb 18, 2012 at 22:00

3 Answers 3


I found a quote from this article

One thing you may not want to do with a press pot, especially a larger model, is use beans roasted less than 2 or 3 days before. What, am I crazy? Nope. There's a problem with ultra fresh beans and it is called "bloom". When beans are only a day or two off the roast, they contain heaps of Co2. Heaps of it, I tell you. That Co2 will translate into a massive bloom of brown suds on top of your press pot, possibly overflowing, but also making it easier for big particulate matter (your ground coffee) to hop and skip over the top of the filter portion when you first apply it. Bloom looks cool, but can make using a press pot more difficult.

The poor filtering part sounds questionable to me, so I googled it and found a few bloom-related comments on this blog post. It seems like some people start timing their soak time only after they see bloom.

This seems like the real reason to me. I know for sure that the air content in ground substances can vary significantly: one cup of flour can contain double the volume of another if one is loosely sifted and the other is compacted. The above quote is accurate about that in my opinion.

Apply this logic to coffee and in order to produce an accurate, general recipe for how long some compounds take to come out of coffee grounds, you need to factor out a variable between coffee grounds: how much air is in the grindings. Maybe the first small pour will saturate with coffee compounds, or drop in temperature quickly, reducing how much it can extract from the grounds. Once it squeezes out all the air, the rest of the water is poured in to do the real extraction work.

  • +1, I think the CO2 is it. I've actually seen that before and wondered what was going on. Recently I've been using beans pre-ground (I know, I know) so haven't had that foaming. Sounds like the "blooming" pre-step is best for freshly ground beans.
    – Sam Ley
    Feb 19, 2012 at 17:43

'bloom' when it comes to French press is the effect that the grounds collect on top of the water when pouring quickly. Presumably this is because of rapid release of carbon dioxide.

If not stirred into the coffee this 'bloom' will cause the grounds to be partially extracted. When wetting the grounds this bloom occurs prematurely, and the force of pouring the remaining water breaks the grounds apart.

I'd say you get the same effect by stirring after 20 seconds or so. :)

  • I have also had good results with stirring after pouring
    – Pat Sommer
    Feb 20, 2012 at 2:05

tl;dr answer is: no well-research reason why, or effect More detailed discussion at https://www.reddit.com/r/Coffee/comments/39t5k2/ive_stopped_doing_blooms_for_now/

Dampening grounds before flowing water over them may improve diffusion (pour over) - but that doesn't apply to French Press because the water just sits and soaks in the coffee anyway (which one assumes you've stirred).

Improving diffusion might have a tangible effect for a pour over due to the water having limited contact with coffee as it flows through.
However, a coffee champ seems to think to think it's not important here, either. https://colinharmon.wordpress.com/2011/03/07/the-bloom/

The first dozen google results on 'blooming coffee effect' describe info like CO2 release, and improved diffusion. If the grounds are homogeneously distributed (stirred to distribute and remove gas), I can't see blooming adding anything.

So, no facts for superior coffee from blooming that I can see. Do some blind testing and make your coffee the way you enjoy it.

  • Hi there. Welcome to Seasoned Advice! I'm finding your answer difficult to understand. You've said the "answer is no" but it's not a yes/no question. It seems like you have some great information here, but is there anyway you could add some structure to make it easier to follow? It's just rather confusing as presented.
    – Preston
    Jul 21, 2015 at 19:05
  • 1
    Maybe I'd had too much coffee! Have edited.. hope it's a little clearer. Jul 23, 2015 at 1:03
  • This is wrong, Max is right and Eric gets to the real point in the latter part of his answer. "it's irrelevant for French Press because the water just sits and soaks in the coffee anyway." is wrong. If you just pour all the water into the dry grounds, the gases released from the grounds cause them to float to the top of the press, and the water is not making full contact with the grounds. You can get around this either by stirring the grounds after pouring the water, or by saturating the grounds before pouring (blooming). Or both. Your two links are both by people who are doing pour-over.
    – Dan C
    Jul 23, 2015 at 12:41

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.