I recently purchased a counter-top, one element 1800W induction cooker, mostly just to see how well the technology worked compared to my gas range.

I took it out of the box and immediately threw about a half inch of water in a cast-iron skillet as a test and set the coil to max power. I noticed that the water began boiling almost immediately (impressive) but in very tight hot spots (two very clear concentric rings, presumably the shape of the coils or some magical physics property of the magnetic fields), taking a long time to spread to other areas (as expected with cast iron).

In fact, the hot spots heated up so quickly that the water was almost completely boiled before the handle had even a hint of warmth, and areas as close as a half inch or so to the hot spots remained cool to the touch for some time after the hot spots were hot enough to boil water.

My question is: Due to the rapid heating and large temperature differentials seen here, in practice does this lead to an increased incidence of cracking cast-iron with induction cookers? If so, what precautions should be taken (e.g. preheat cast-iron at a lower power first, only use cookware designed specifically for induction, etc.)?

4 Answers 4


Cracking? No, not in my experience. I own like 20 cast iron skillets (I've been told I have a problem).

Warping? Yes. I have a 2,800 watt per burner commercial induction stove with a very small pattern like yours. If you repeatedly overheat a pan on high for searing, it will eventually bow outwards. Warping can be mitigated by preheating your pan gently.

That said, if the pan is full of water or oil (for deep frying, not stir fry) there is nothing to fear. I have had the same stainless stock pot for 8 years and I roast it on high all the time (with liquid). Water is a very effective coolant (it's what keeps your car engine from overheating). The likelihood that a pan full of water will overheat is very unlikely, nigh impossible.

RE: comments. Yes it is a lot of skillets. This is what 14 looks like.

  • 1
    20 might be a lot if the're all skillets. My mom has a problem as she's been only collecting Wagner and Griswold, and is trying to have at least one of anything. I don't know how much she has, but she has some shelves filled in the kitchen, plus a rack that holds another 8+ skillets, and a stand for dutch ovens.
    – Joe
    Commented Mar 13, 2015 at 13:32
  • That's a lot of skillets. Off topic, do you just towel dry them if you wash them? Usually I dry them back on a low flame, but drying makes me uncomfortable (may be unwarranted, given your answer) on the induction coil because of the quick, uneven heating. If I wanted to just stay with the induction cooker, I think I have to find new cleanup/drying/oiling habits.
    – Jason C
    Commented Mar 13, 2015 at 17:16
  • If you keep it on low to medium I don't see a problem. If you're a purist you never clean them with anything but oil and coarse salt. If soap and water come to the party I just hand dry and flip upside down.
    – Derpy
    Commented Mar 13, 2015 at 19:40
  • 1
    Also, if you wash your pots immediately after cooking with hot water they will dry themselves with residual heat. Just don't burn yourself.
    – Derpy
    Commented Mar 13, 2015 at 19:41

Having nothing to do with induction stoves, you should always preheat your cast iron or any pan for that matter.

Adding a bit more to my answer, although you have to take more care not to break the top of your stove, cast iron and induction stoves are a marriage made in cooking heaven. They are very well suited for one another.

Nothing beats an actual flame to monitor, but once you know your equipment, this is an excellent pairing.

  • Preheating it on that induction device would mean heating it dry, and given that many induction burners use slow cycling (cycles measured in seconds) rather than real power control, this might make matters far worse. Additionally, as described, the heating is uneven - also making things worse with dry cookware. Commented May 9, 2016 at 10:24
  • @rackandboneman So you don't recommend preheating? Just want to be clear here
    – Escoce
    Commented May 10, 2016 at 9:33
  • 2
    I would not recommend preheating anything empty on an inexpensive induction cooker. Reasoning behind it: From my own experience, they can make oil-coated spots on cookware smoke within a minute. Commented May 10, 2016 at 14:21
  • 1
    I think knowing your equipment is what's key. That was my last statement in my answer.
    – Escoce
    Commented May 11, 2016 at 5:13

To answer the question of precautions:

  1. Pre-heat at a lower temperature first. I find that with an induction burner, I often don't have to go and use the highest setting at all.

  2. If you want to heat it quickly, put a bit of water in it (at least 1cm / ~1/2 inch ... might need more if your burner heats really unevenly) before heating, and then when the pan's nearly to where you want it, pour out the water and turn down the heat to where you want it and either wipe it out or give it a minute to dry from the heat.

It's difficult to measure just how significant of a problem this might be, as it's possible that the non-ring area is only a few degress below the hotest area ... or it might be significantly off. As the water initially heats, the disolved gases will come out of the water and if the heat differential is causing convection, you might see quite a bit of it with none of it happening elsewhere. You might need an IR thermometer and heat a dry pan to see how severe the temperature gradient is.


Definitely possible. My wife cracked a cast-iron round griddle when she was experimenting with a stand-alone induction burner she had just gotten. She just put the griddle on it, turned it up to high, and BAM! The griddle was cracked from the edge to the center. It was one that had belonged to my grandmother, and had survived 50 or 60 years or more of regular use on gas and electric stoves. But the first time on an induction burner ruined it immediately. I'd certainly recommend bringing all cookware up to heat gradually, with a minute or two on a low setting before moving to higher heat.

Not the answer you're looking for? Browse other questions tagged or ask your own question.